{"product_id":"cicada-cmb69-4-24chdlid-bundle-2024","title":"Cicada Audio CMB69.4 + 24CHDLID — 6×9″ Mid-Bass Saddlebag Lid Bundle (4Ω) for 2024+ H-D® Touring","description":"\u003ch2\u003eDedicated 6×9″ mid-bass for the saddlebag lids of 2024+ H-D® Touring — speakers and cut-in kit in one bundle\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eSeptember bundle offer — ends 30 September 2026.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThis bundle pairs the Cicada Audio® \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-cmb69-4-6-9-pro-mid-bass-carbon-matrix-4o\"\u003eCMB69.4\u003c\/a\u003e Pro Mid-Bass speakers (4Ω, pair) with the \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-24chdlid-6x9-saddlebag-lid-cut-in-kit-2024-harley-touring\"\u003e24CHDLID 6×9″ Saddlebag Lid Cut-In Speaker Kit\u003c\/a\u003e. On bikes with standard solid saddlebag lids, adding 6×9-inch rear speakers requires either replacement speaker lids or a cut-in lid kit. The 24CHDLID is the cut-in route: you keep your factory painted lids, and the kit supplies the templates, baffles, grilles and gasketing to cut, mount and finish the openings.\u003c\/p\u003e\n\n\u003ch3\u003eWhat’s in the bundle\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-cmb69-4-6-9-pro-mid-bass-carbon-matrix-4o\"\u003eCicada Audio CMB69.4\u003c\/a\u003e — 6×9″ Pro Mid-Bass speakers (pair).\u003c\/strong\u003e 4Ω, 150W RMS, 88 dB sensitivity, Carbon Matrix Composite™ (CMC™) cone, 38 mm Black Coat™ OFC voice coil, die-cast aluminium basket with Vortex Flow Venting™, and Rain or Shine™ all-weather construction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-24chdlid-6x9-saddlebag-lid-cut-in-kit-2024-harley-touring\"\u003eCicada Audio 24CHDLID\u003c\/a\u003e — 6×9″ saddlebag lid cut-in kit (left and right).\u003c\/strong\u003e Includes a three-part top-load assembly (powder-coated steel grille, angled UV-resistant ASA baffle and gasketed clamping ring), ABS cut-out templates (L\/R), die-cut speaker gasketing, lid gasket seals, rainproof lid covers, and tethers with a crossover pouch. Speakers mount in the kit; no lids are supplied.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWho this is for\u003c\/h3\u003e\n\u003cp\u003eRiders on 2024+ H-D® Touring models adding an amplified rear stage to the saddlebag lids, who want dedicated mid-bass drivers rather than coaxials in that position, and who run — or are adding — an amplifier with DSP crossover control.\u003c\/p\u003e\n\u003cp\u003eThis is the \u003cstrong\u003e4Ω version\u003c\/strong\u003e. Choose it if you bridge amplifier channels for the rear pair, or if the rest of your system runs at 4Ω. Bridging halves the load the amplifier sees, so a 4Ω speaker presents 2Ω on a bridged channel — within the rated minimum of amplifiers like the FLX700.4PRO and FLX1400.4PRO. A 4Ω load also draws less current at the same volume, which gives the amplifier more thermal margin on a long, hot day.\u003c\/p\u003e\n\u003cp\u003eRunning a 2Ω-stable channel in stereo instead? The \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-cmb69-2-6-9-pro-mid-bass-carbon-matrix-2o\"\u003eCMB69.2\u003c\/a\u003e version of this bundle is the one to choose.\u003c\/p\u003e\n\n\u003ch3\u003eWhat the rear stage adds — and what it doesn’t\u003c\/h3\u003e\n\u003cp\u003eThe CMB69.4 adds lower-midrange weight and output from the saddlebag lids, with more sound behind the rider and better coverage for a pillion. Levelled and time-aligned properly, it provides rear fill; set too loud or with the wrong delay, it pulls the sound image backwards. \u003cstrong\u003eIt is not a subwoofer or low-bass stage.\u003c\/strong\u003e With the required high-pass in place, the CMB69.4 will not produce deep kick-drum weight or sub-bass.\u003c\/p\u003e\n\u003cp\u003eThe CMB69.4 is also a mid-bass driver only — it is specified to 1 kHz and has no tweeter. On its own in the lid it covers the lower midrange. For a two-way rear stage, add a tweeter pair on the \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-24chd69tb-6x9-tweeter-bridge-2024-harley-touring\"\u003e24CHD69TB\u003c\/a\u003e tweeter bridge, crossed over through your DSP.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eOn the road: more output and presence from behind at highway speed, and a pillion who can actually hear the system — provided it is tuned to support the front speakers rather than compete with them.\u003c\/em\u003e\u003c\/p\u003e\n\n\u003cdiv\u003e\n\u003ch3\u003e⚠️ Before you order: a high-pass crossover and an external amplifier are required\u003c\/h3\u003e\n\u003cp\u003eThe CMB69.4 must not be run full-range or from factory radio power. In a sealed saddlebag lid, the required high-pass is \u003cstrong\u003e250 Hz @ 24 dB\/octave, or 300 Hz @ 12 dB\/octave minimum\u003c\/strong\u003e. Lower settings in a sealed lid risk over-excursion and permanent damage to the driver.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow to check your system:\u003c\/strong\u003e if your amplifier has built-in DSP (FLX700.4PRO, FLX1400.4PRO) or you run a DSP412PRO, you can set the high-pass in the tuning software. If your amplifier’s crossover can’t reach 250 Hz @ 24 dB\/octave (or 300 Hz @ 12 dB\/octave), you’ll need a DSP or a passive high-pass filter at the correct frequency. Correct crossover, gain and limiter settings matter here — if you’re unsure, contact us before ordering and we’ll check it against your setup.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch3\u003eWhat else you’ll need\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAn amplifier with DSP crossover control\u003c\/strong\u003e — the \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-flx700-4pro-ultra-compact-4-channel-dsp-amplifier\"\u003eFLX700.4PRO\u003c\/a\u003e or \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-flx1400-4pro-4-channel-dsp-pro-amplifier\"\u003eFLX1400.4PRO\u003c\/a\u003e, or a \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/dsp412pro-4-input-x-12-output-dsp-processor-w-diald-software\"\u003eDSP412PRO\u003c\/a\u003e ahead of your existing amplifier.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eA signal source for the amplifier\u003c\/strong\u003e — 2024+ Touring models running Skyline OS need an A2B interface such as the \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/nav-tv-zen-h-8-channel-a2b-audio-interface-harley-touring-2023-5-plus\"\u003eNAV-TV ZEN-H\u003c\/a\u003e to feed an aftermarket amplifier.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLid speaker wiring\u003c\/strong\u003e to suit where your amplifier is mounted — contact us and we’ll confirm the right harness for your bike.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOptional, for a two-way rear stage\u003c\/strong\u003e — the \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-24chd69tb-6x9-tweeter-bridge-2024-harley-touring\"\u003e24CHD69TB\u003c\/a\u003e tweeter bridge with \u003ca href=\"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-audio-rr075t-titanium-shallow-horn-tweeters\"\u003eRR075T\u003c\/a\u003e tweeters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBike\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e2024+ H-D® Touring models with standard solid saddlebag lids, including Street Glide® and Road Glide®\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePosition\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eSaddlebag lids — cut-in (permanent modification to the lid; templates included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eNot compatible\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e2014–2023 H-D® saddlebag lids\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSpeaker cutout \/ depth\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e145 × 216 mm (5.7″ × 8.5″) \/ 99 mm (3.9″)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003c\/p\u003e\n\u003cp\u003eCutting a factory lid is permanent. The ABS templates in the kit are there to get the openings right first time, and we recommend professional installation if you haven’t cut lids before.\u003c\/p\u003e\n\n\u003ch3\u003eThe bottom line\u003c\/h3\u003e\n\u003cp\u003eA dedicated 4Ω 6×9″ mid-bass pair and the matching cut-in kit for 2024+ H-D® Touring saddlebag lids, bundled for September. It adds output and rear coverage to an amplified, DSP-controlled system — set the high-pass before first power-up. Running a 2Ω-stable channel in stereo? See the CMB69.2 version. Questions about your system? Call us on 07 3350 1354 or email sales@motorcycleaudio.com.au.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBundle offer ends 30 September 2026.\u003c\/strong\u003e\u003c\/p\u003e","brand":"Cicada Audio","offers":[{"title":"Default Title","offer_id":51166880596215,"sku":"CMB69.4+24CHDLID","price":940.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0901\/6505\/1639\/files\/temp_dz89WGv.png?v=1789521935","url":"https:\/\/www.motorcycleaudio.com.au\/products\/cicada-cmb69-4-24chdlid-bundle-2024","provider":"Motorcycle Audio Australia","version":"1.0","type":"link"}